- ANILAM SERIES 1100 HOW TO
- ANILAM SERIES 1100 MANUALS
- ANILAM SERIES 1100 DRIVERS
- ANILAM SERIES 1100 MANUAL
- ANILAM SERIES 1100 CODE
It also makes more sense when you have the controller in front of you.
ANILAM SERIES 1100 MANUAL
We'll have to sort out details like adding home switches, incoming mains switching, stuff like that, but nothing too complicated, I hope.Well so far I'm very satisfied with SZGH and the manual isn't that bad after you have read it a few times.
![anilam series 1100 anilam series 1100](https://www.picclickimg.com/d/l400/pict/324202049960_/Anilam-1100-CNC-milling-machine-Memory-Board-PN.jpg)
ANILAM SERIES 1100 HOW TO
You aren't going to learn how to build a CNC machine from scratch with them but if you know what you are doing it seems ok.
ANILAM SERIES 1100 MANUALS
I've been through the SZGH manuals and while they are not exactly perfect English, to date they seem pretty good. It's a few hundred quid more than using the SZGH 1000mdb controller with new DC drives and existing motors but it should be simpler to put together - probably not the route I would have taken if it were my own machine but he wants to be up and running with minimum fuss and I don't want another project. He has organised someone to make up adaptor plates for the new AC servos, to replace the SEM motors. My friend has ordered a pallet-load of kit from SZGH. If it were my machine, I would probably spend a bit more time on investigation but this machine belongs to someone who wants to use it, not turn it into a project! It's not my machine or my money that's being spent although I would tend to favour the all-new setup. Only one upper limit and one lower limit switch input so all axes share these, which is why I'm not sure about home switches - there might be some other inputs for these but still decoding Chinglish for those. Can't see from first look at manual if you can use limit switches as home switches but I can ask them. To date, SZGH have been very quick with supplying manuals and quotation. Needs adaptor plate or similar to fit machine but all new technology, low technical risk, and if it all comes from SZGH, it's more-or-less pre-configured from the factory complete with cables.
ANILAM SERIES 1100 DRIVERS
Need to update controller anyway but servo options are new dc drives (CNCdrive?) assuming that there are encoders fitted, costing around £300, or new ac servos plus drivers for around £750. I've seen an article about updating a similar system which used an encoder but I've no idea how standardised these systems are. Label has spec for tacho output but don't know if there is a resolver or encoder. Servo motors are badged Anilam (well, one of them has a barely-legible label). No big issue either way - it's only another cable. Still thinking about whether it's worth using electronic speed control as there's no tool changer so setting speed manually at the same time as manual tool change isn't a big deal. Is this because I have a early version, or am I missing something more fundamental ? I'm sure some of these issues must have been resolved before, and it would be great to get this code to run as intended.Spindle motor is driven by Mitsubishi VFD but not using variable speed as there is a continuously-variable pulley drive (plus back gear) on the mill. The console message was : 'Error 'Stop spindle before Fwd / Rev command.' I had a similar issue at Line 34, though on the next attempt, it ran the program past this point unchallenged. this consistently gave a console message of 'Error : Must stop spindle before tool change'. Whilst the above lines were missing, the following line halted the program run, which I could not seem to restart : This includes the following (and any repeats) :
ANILAM SERIES 1100 CODE
The oddities mainly consist of code lines that did not appear on my mill console (despite being transmitted) I am guessing they could not be translated. There seem to be a couple of show stoppers for me in the generated code.įrom the sample code, (Oct 2017) the machine did not load the lines for Arc Cw, or Arc Ccw, they are missing, not even a blank line shown. Later I came across the 'Sample' code in the Autodesk CAM posts section, and downloaded that, and fed it to the mill, getting a very similar result. I was very pleased that the mill seemed to accept it, and ran some of it, though there were some lines missing. With the help of a pal to try it out, we drew a simple cube with rounded corners and a hole machined in the centre and generated a CAM file for the mill, using Anilam Conversational post processor. It is brilliant that the Fusion360 has a CAM interface for so many machines including Anilam Conversational. At the bottom of the welcome screen it says Version 6.42A. It has no hard drive, so I load larger programs via DNC (- does anyone know if it is possible to retrofit a hard drive ?). Hello, I have recently purchased an Ajax three axis cnc mill with Anilam 1100M CNC controls. siemens-840d error Danger of collision due to tool radius compensation 1.post-proccesor philips cnc 532 5 axis 1.Haas (pre-NGC) haas Post processor edit Help 1.